Inspection
Inspection Schedule
Inspection items are divided into five stages (daily, 1-month, 3-month, 6-month, and 12-month), with additional items added at each stage. However, if the Manipulator is powered and operated for more than 250 hours in a month, add inspection items every 250, 750, 1500, and 3000 hours.
| Inspection Item | ||||||
|---|---|---|---|---|---|---|
| Daily Inspection | 1-month Inspection | 3-month Inspection | 6-month Inspection | 12-month Inspection | Overhaul (Parts Replacement) | |
| 1 months (250 hours) | Perform daily | ✓ | ||||
| 2 months (500 hours) | ✓ | |||||
| 3 months (750 hours) | ✓ | ✓ | ||||
| 4 months (1,000 hours) | ✓ | |||||
| 5 months (1,250 hours) | ✓ | |||||
| 6 months (1,500 hours) | ✓ | ✓ | ✓ | |||
| 7 months (1,750 hours) | ✓ | |||||
| 8 months (2,000 hours) | ✓ | |||||
| 9 months (2,250 hours) | ✓ | ✓ | ||||
| 10 months (2,500 hours) | ✓ | |||||
| 11 months (2,750 hours) | ✓ | |||||
| 12 months (3,000 hours) | ✓ | ✓ | ✓ | ✓ | ||
| 13 months (3,250 hours) | ✓ | |||||
| ︙ | ︙ | ︙ | ︙ | ︙ | ︙ | ︙ |
| (20,000 hours) | ✓ | |||||
Inspection Details
Inspection items
| Inspection Item | Inspection Location | Daily Inspection | 1-month Inspection | 3-month Inspection | 6-month Inspection | 12-month Inspection |
|---|---|---|---|---|---|---|
| Loose bolts: Check for rattling | Hand mounting bolts | ✓ | ✓ | ✓ | ✓ | ✓ |
| Manipulator installation bolts | ✓ | ✓ | ✓ | ✓ | ✓ | |
| Check for loose connectors | Manipulator side external (Connector plate, etc.) | ✓ | ✓ | ✓ | ✓ | ✓ |
| Inspect for flaws Clean off adhering debris, etc. | Entire Manipulator | ✓ | ✓ | ✓ | ✓ | ✓ |
| External cables | ✓ | ✓ | ✓ | ✓ | ||
| Correct deformations and misalignments. | Safety barriers, etc. | ✓ | ✓ | ✓ | ✓ | ✓ |
| Check brake operation | Joint #3 | ✓ | ✓ | ✓ | ✓ | ✓ |
| Check for abnormal operation noise and vibration | Entire Manipulator | ✓ | ✓ | ✓ | ✓ | ✓ |
Inspection methods
| Inspection Item | Inspection Method |
|---|---|
| Check for loose or rattling bolts | Using an Allen wrench or similar tool, check that the hand mounting bolts and Manipulator installation bolts are not loose. If the bolts are loose, refer to the following section, and retighten to the proper torque. Tightening the Hexagon Socket Head Cap Bolts |
| Check for loose connectors | Check that no connectors are loose. If a connector is loose, reattach it so that it will not come off. |
| Inspect for flaws Clean off adhering debris, etc. | Check the appearance of the Manipulator, and clean off any dust or other foreign substances adhering to it. Check the appearance of the cables for any flaws, and make sure it is not disconnected. |
| Correct deformation and misalignment | Check for misalignment of safety barriers and other components. If it is misaligned, correct it to the original position. |
| Check brake operation | With the motor turned off, check that the shaft does not drop. If the shaft drops while the motor is turned off and the brake is not released, contact the supplier. Also, contact the supplier if the brakes do not release despite performing the brake release operation. |
| Check for abnormal operation noise and vibration | Check for any abnormal noises and vibrations during operation. If you notice anything unusual, contact the supplier. |